What it is
An iron-based titanium-alloy family for Ti alloying, nitrogen fixation, grain and inclusion design in selected steel grades; Ti grade, Al/Si/C/N/O residuals and addition point require grade-specific review.
Ferroalloys · Special alloys
Ferrotitanium
An iron-based titanium-alloy family for Ti alloying, nitrogen fixation, grain and inclusion design in selected steel grades; Ti grade, Al/Si/C/N/O residuals and addition point require grade-specific review.
Product codeFA-FETI
Industry application1
Key indicatorsTi / Fe · Al / Si / C · P / S / N / O及其他残余
Order boundaryQuotation and order confirmation
QUICK DECISION
Four answers before reading the technical detail
This section supports initial screening; final grade, addition and effects require operating conditions, formal documents and plant validation.
What it does
- Titanium alloying
- Nitrogen fixation and precipitation control
- Support for grain and inclusion design
Where it fits
- Late alloying after adequate deoxidation and slag control
Boundary not to miss
- Early addition, high oxygen potential or excess Ti can cause low recovery, Ti oxide/nitride clustering, castability or performance problems
SELECTION BOUNDARY
Start with the selection boundary
Ferrotitanium is only for grades with an explicit Ti metallurgy design; it is not a routine addition to every RH, VD, AOD or LF heat and is not automatically interchangeable with ferrotitanium cored wire.
PRODUCT MANUFACTURING
Product manufacturing process
Feeds and smelting routes for special ferroalloys vary by alloy system and producer and may use electric-furnace reduction, metallothermic reduction or another route verified by standards/supplier documents. Commercial preparation generally includes feed review, controlled reaction or smelting, slag/metal separation, casting/cooling, crushing/screening, representative sampling and lot testing. The page does not assume Jinsheng owns such a line.
- 01Confirm target-element feed, iron source, reductants, fluxes and actual route
- 02Run the controlled electric-furnace or metallothermic reaction under manufacturer documents, managing temperature and homogeneity
- 03Separate slag/metal, cast or form, cool and segregate the lot
- 04Crush, screen and sample representatively, then test principal elements and limiting residuals
- 05Pack by grade, sizing and order requirement with traceability
SPECIFICATIONS & PACKAGING
Grades, specifications, indicators and packaging
A ferrotitanium specification must use GB/T 3282—2012 and actual supplier documents to fix Ti and the iron matrix and control Al, Si, C, P, S, N, O and other grade-sensitive residuals, together with form, sizing, fines, pack, sampling and COA. The page does not present standard grade ranges as Jinsheng guarantees and assumes no Ti content.
- 01Confirm formal product identity, applicable standard, supplier grade and actual production route
- 02Fix principal chemistry, limiting items, physical indicators and the corresponding test methods
- 03Confirm form, size distribution, fines, moisture, flowability or unit mass for storage, handling and charging equipment
- 04Confirm pack, label, TDS, SDS/PSI, sampling rules and lot COA
GRADES & SPECIFICATIONS
Grades, specifications, indicators and packaging
Supply specifications, packaging, lead time and quality documents are subject to the formal quotation and order confirmation.
| Grade / family | Chemistry | Size and form | Packaging |
|---|---|---|---|
| Specification direction 01FerrotitaniumConfirm grade, applicable standard and guaranteed values before quotation |
| Confirm against the addition method, equipment and order requirements | Confirm pack format, net weight and labels in the quotation and order |
ORDER SPECIFICATION CONFIRMATION
What must be confirmed before this becomes an order specification
Supply specifications, packaging, lead time and quality documents are subject to the formal quotation and order confirmation.
- 01Confirm the product, grade, application and supply scope
- 02Fix guaranteed chemistry, sizing, form and packing in the quotation and order
- 03Agree sampling, test methods, acceptance rules and lot COA fields
- 04Confirm the required TDS, SDS/PSI, labels and delivery documents
SELECTION AND COMPARISON
Compare specification directions by indicators and operating conditions
Supply specifications, packaging, lead time and quality documents are subject to the formal quotation and order confirmation.
01Specification direction
Ferrotitanium
Compare the key indicators below, then confirm grade, guaranteed values, sizing and packing against the operating conditions.
- Key indicators
- Ti / FeAl / Si / CP / S / N / O及其他残余
- Size and form
- Confirm against the addition method, equipment and order requirements
- Packaging
- Confirm in the quotation and order
INDUSTRY APPLICATION
Industry, furnace, material and addition point
Confirm the process position before method and quantity calculations; an application relationship for one furnace or material must not be copied to another.
Steelmaking plants
Late alloying after adequate deoxidation and slag control
- Furnace / equipment
- LF, post-RH ladle, post-VD or reviewed steel-foundry ladle
- Material / output
- IF/HSLA, stabilized stainless and other Ti-designed steel grades
APPLICATION METHOD
Use scenarios, method, effect and risk validation
Ferrotitanium is used for IF/HSLA, stabilized stainless or another steel with a Ti metallurgy design, generally added late in the ladle after adequate deoxidation and slag control. Calculate from net Ti increase, lot Ti and site recovery while coordinating O/N/Al, dissolution and rolling/heat treatment. A matched practice can support nitrogen fixation, precipitation and grain design; early/excess addition or high oxygen potential can lower recovery and create Ti oxide/nitride, castability or performance risk. Verify steel samples, inclusions and performance.
- 01Confirm steel grade, process point, equipment, initial state, process objective and prohibited conditions
- 02Check the actual SKU, lot COA, TDS, SDS/PSI and site history
- 03Run a small site trial from mass/heat balances or the equipment window without copying a fixed cross-plant dose
- 04Resample or record slag, steel, temperature, equipment response, defects and performance before approval, correction or stop
PROBLEM AND SOLUTION
From operating objective to effect verification
Each application explains the role, method, quantity principle and risk boundary; the final proposal is confirmed against operating conditions and lot documents.
01
Steelmaking plants
Late alloying after adequate deoxidation and slag control
- Furnace / equipment
- LF, post-RH ladle, post-VD or reviewed steel-foundry ladle
- Material / output
- IF/HSLA, stabilized stainless and other Ti-designed steel grades
- Method
- Choose timing and form from Ti, N, O, Al and precipitation design, ensuring rapid immersion, dissolution and mixing while limiting reoxidation.
- Quantity determination
- Calculate from net Ti increase, measured lot Ti and site recovery, with Al, Si, C, N and O carry-in as constraints.
Expected effects
- Can establish target Ti and support precipitation, grain or stabilization design when chemistry and thermomechanical practice match
Limits and risks
- Early addition, high oxygen potential or excess Ti can cause low recovery, Ti oxide/nitride clustering, castability or performance problems
STORAGE & SAFETY
Storage, handling and risk
- Keep dry and control crushing dust; hot-steel addition must prevent bridging, splashing and undissolved large pieces.
This section does not replace the company's final SDS/PSI or the plant safety procedure.
REFERENCE AND ORDER BOUNDARY
Use industry references to understand, then order documents to confirm
Supply specifications, packaging, lead time and quality documents are subject to the formal quotation and order confirmation.
DOCUMENTS & MEDIA
Images, TDS, SDS and COA
Document availability depends on the product, lot, destination market and order agreement.
TDS
Confirms product identity, guaranteed indicators, sizing, form and packing.
SDS / PSI
Confirms storage, handling, protection and market-specific safety information.
COA
Links a specific lot to test items, results, methods and issue information.
INDUSTRY TECHNICAL REFERENCES
Selected external reference material
The following items come from licensed public media or original producer websites and explain similar products or typical processes only. They are not Jinsheng photographs, TDS, SDS or lot COA and create no supply commitment.
COA field template (not a certificate)
A blank structure for lot, chemistry, sizing, method, disposition and issue data. It contains no test result and cannot be used for delivery.
Jinsheng blank COA field template · 2026-08-14Open field template ↗SOURCES
Public references and verification dates
- GB/T 3282—2012 Ferrotitanium, official record ↗Standard · 2026-08-19
Public sources supplement general facts; they do not replace Jinsheng's formal product specification, TDS or lot COA.
INQUIRY PREPARATION
Prepare these operating conditions for a more precise technical response
Please provide the specification, quantity, destination, and contact information.
Already includedFA-FETIFerrotitanium
- 01Target industry, steel grade or casting material
- 02Furnace type, equipment, melt weight and current operating practice
- 03Measured chemistry, target chemistry and permitted residuals
- 04Planned addition point, temperature, slag and stirring conditions
- 05Current product, addition, recovery or operating-issue record
- 06Required size, form, packaging, quantity and destination
- 07Available melt analysis, microscopy, photographs or trial results
TECHNICAL AND QUOTATION CONSULTATION
Send the operating conditions for human review
Domestic inquiries are handled by the Domestic Sales Department and international inquiries by the International Sales Department. Price, availability and lead time are confirmed for each inquiry based on specification, quantity and delivery location.